Apologies if this is a dumb question, but I have not figured out an easy way to remove the front tire, and thought about asking if there is a better way.
The way I do it is by removing the front fender first in order to free-up the caliper pipes and therefore the calipers. This creates the space ...
Search found 8 matches
- Wed Apr 27, 2022 1:05 pm
- Forum: Chassis & Suspension Shop
- Topic: 900 GTE Front tire removal
- Replies: 1
- Views: 7359
- Wed Apr 27, 2022 12:57 pm
- Forum: Chassis & Suspension Shop
- Topic: 860 gt Moving forks up 5mm in Triple Clamps??
- Replies: 5
- Views: 16053
Re: 860 gt Moving forks up 5mm in Triple Clamps??
I don't know on the Ducati, but I race enduro and in the dirtbike 5 mm is very noticeable in stability and cornering agility. The more you move them up the more agile but you will have the risk of inducing headshake.
In my Honda CBX I raised the rear 5 mm (which is the same effect) and it developed ...
In my Honda CBX I raised the rear 5 mm (which is the same effect) and it developed ...
- Wed Apr 08, 2020 7:17 am
- Forum: Electrical & Gauges Shop
- Topic: Removing rubber gauge holder cup
- Replies: 3
- Views: 14313
Re: Removing rubber gauge holder cup
If you have access to a heat gun, you could try a very gentle application of heat just to warm the rubber and make it more supple. Maybe try squeeze a thin feeler gauge between the rubber part and the clock and spray in some lubricant then work the feeler gauge around the clock.
Thanks, I ...
- Tue Apr 07, 2020 8:21 pm
- Forum: Electrical & Gauges Shop
- Topic: Removing rubber gauge holder cup
- Replies: 3
- Views: 14313
Removing rubber gauge holder cup
Hi,
I have been trying to remove the rubber holder cup from my speedometer but it is very tight and I cannot move it at all. I replaced them around 18 months ago and they went in just fine without any special treatment. Any trick to getting them out? I would hate cutting it.
Thanks.
Ramon
I have been trying to remove the rubber holder cup from my speedometer but it is very tight and I cannot move it at all. I replaced them around 18 months ago and they went in just fine without any special treatment. Any trick to getting them out? I would hate cutting it.
Thanks.
Ramon
- Sat Apr 27, 2019 6:29 am
- Forum: Electrical & Gauges Shop
- Topic: 900 GTS Tachometer
- Replies: 5
- Views: 22149
Re: 900 GTS Tachometer
Thanks to all.
For now I lubed the cable to see if it gets better. Hardest part was fighting the rubber boot. How you guys take that off? It’s just so hard.
Thanks again.
For now I lubed the cable to see if it gets better. Hardest part was fighting the rubber boot. How you guys take that off? It’s just so hard.
Thanks again.
- Wed Apr 24, 2019 7:01 am
- Forum: Electrical & Gauges Shop
- Topic: 900 GTS Tachometer
- Replies: 5
- Views: 22149
900 GTS Tachometer
Hi, I don't know if this is the correct place to post this question.
(Admin edit: I moved this to it's current location)
On my 78 900 GTS the tachometer started to act very strange. At 4k rpm or so, the needle is dancing all over the place. When at idle it works fine. Any guess on where to start ...
(Admin edit: I moved this to it's current location)
On my 78 900 GTS the tachometer started to act very strange. At 4k rpm or so, the needle is dancing all over the place. When at idle it works fine. Any guess on where to start ...
- Sun Jul 02, 2017 8:23 pm
- Forum: Engine & Transmission Shop
- Topic: 860GT base gasket question
- Replies: 7
- Views: 17985
Re: 860GT base gasket question
He is referring to Permatex copper gasket sealant not a copper base gasket.
I don't have much time to work on the bikes and can't afford to get it wrong in the first try. Thats why I use a very thin layer of Permatex High Tack gasket sealant on every gasket. It does not dry and helps in case there ...
I don't have much time to work on the bikes and can't afford to get it wrong in the first try. Thats why I use a very thin layer of Permatex High Tack gasket sealant on every gasket. It does not dry and helps in case there ...
- Thu Jun 29, 2017 5:33 pm
- Forum: Introduce Yourself
- Topic: New member from Mexico City
- Replies: 1
- Views: 8505
New member from Mexico City
Hello everybody. For months I have been an avid reader of this forum. All started when I won, without wanting to win, a 78 GTS in E-bay. I though price was low and someone else would bid higher. Well, neither the price was low or someone else went for it. Imagine my face, me in Mexico city and some ...