Valve Additive for Unleaded Fuel

Post your 'Carburettor & Fuel System' FAQs, comments & questions regarding Ducati motorcycles here.
Rick F
Mach 3
Posts: 89
Joined: Mon Aug 07, 2006 6:35 pm
Location: Murwillumbah NSW AUstralia

Valve Additive for Unleaded Fuel

Post by Rick F »

Just want ask for some advice re fuel additives for a 750GT.

As I understand it, we are all adding an additive to our fuel for the older Ducks, to protect the valves (?)

I am following the instructions on the bottle 1ml/litre (1.5fl.oz/10 gallons)

My questions are:

1) can you add too much? (what would be an accepted tolerance?)

2) if NOT added, how long before damage is done?

Living in a regional area, it may not always be available & I want to know how diligent I need to be about carrying some with me.

There is a local bevel/desmo specialist, and he suggests just to "throw a bit in every 3 or 4 tankfuls"

Thanks
Rick
User avatar
DesmoDog
750 GT
Posts: 156
Joined: Fri Mar 19, 2004 10:26 am
Location: Dexter, MI USA
Contact:

Re: Valve Additive for Unleaded Fuel

Post by DesmoDog »

Rick F wrote:Just want ask for some advice re fuel additives for a 750GT.

As I understand it, we are all adding an additive to our fuel for the older Ducks, to protect the valves (?)
I'm not. The heads have seats installed in them that can handle unleaded gas just fine from what I can tell. Not that I ride the GT enough for valve recession to be a problem...
Peter Mille
750 SS Greenframe - the holy grail
Posts: 500
Joined: Fri Aug 13, 2004 2:12 am
Location: The Netherlands, Europe.

Post by Peter Mille »

When I had the heads of my '85 mille serviced by Bevel guru Steve Wynne in England some years ago, he strongly advised me, to avoid valve problems, to use LEADED fuel, if not available, to use a good additive!
So from that point on, I use the right amount Millers VSP (valve seat protection) additive at every tank filling with Shell V-Power 98 octane fuel. www.millersoils.co.uk
If an "expert" says your engine can run on unleaded, have him that written down, and have him responsible for fuel related problems..I bet he will not do that....!!
Nick
Diana
Posts: 63
Joined: Wed May 10, 2006 3:40 pm
Location: On da Rock

Post by Nick »

I've never added lead to my unleaded fuel, I ride the @#$ out my stable of British and Italian classic bikes and I've never had any valve-related problems, the valves seldom need adjusting and the bikes run fine. I think its all just a lot of worry about nothing. (My 45-year-old car also runs fine on unleaded!)
From probably the only person in the world who rides a Ducati 350 Sebring for daily transportation.
Laurence
Cucciolo - the Lil Pup
Posts: 5
Joined: Sat Apr 22, 2006 4:38 am
Location: New Zealand

Post by Laurence »

I ran 2 identical japanese motorcycles for 100 000 km each on the same maintainence program, one on leaded and one on unleaded fuel
The manual recomended leaded fuel only.
I did a valve job on the one that ran leaded at 60k and nothing to the one i ran on unleaded..
Since that experiment ive been of the opinion that the fuel additive gag is the same as the Y2K gag that was going to destroy all our computers and end the world as we know it..
linblad
Cucciolo - the Lil Pup
Posts: 8
Joined: Thu Jul 29, 2004 12:20 am
Location: s.e asia

fuel additives

Post by linblad »

get ya heads done so it takes unleaded contact justin at protwin in perth 0412924308 he used to work at veetwo and since they no longer do engine work as they goy bought out he went on his own, had mine done 4 years ago fantastic stick any unleaded fuel in her no dramas ! good luck linblad.
User avatar
78SS
Cucciolo - the Lil Pup
Posts: 9
Joined: Mon Feb 05, 2007 6:02 pm
Location: New Zealand
Contact:

unleaded gas

Post by 78SS »

My SS runs like a 2 stroke on unleaded, fouls plugs alot, so I have to buy expensive race gas to run it. I have had it tuned by professional mechanics who I trust. Anyone else have this problem or is it just me?
Peter Mille
750 SS Greenframe - the holy grail
Posts: 500
Joined: Fri Aug 13, 2004 2:12 am
Location: The Netherlands, Europe.

Post by Peter Mille »

Maybe your plugs are to cold?
User avatar
78SS
Cucciolo - the Lil Pup
Posts: 9
Joined: Mon Feb 05, 2007 6:02 pm
Location: New Zealand
Contact:

Post by 78SS »

Hi Peter, I am running standard plugs and they run fine on leaded gas, I have found unleaded petrol does not fully combust in any engine leaving a oily coating in the tail pipe.
Gomi

Post by Gomi »

Do you have stock pistons or High Compression ones?
HC pistons often require a greater octane fuel... maybe is this the reason.
Peter Mille
750 SS Greenframe - the holy grail
Posts: 500
Joined: Fri Aug 13, 2004 2:12 am
Location: The Netherlands, Europe.

Post by Peter Mille »

I did run the standard plugs as well, the instruction manual of my '85 Mille stated to use Bosch W3B.
Later, Bosch advise to use in a Mille Engine Bosch W5B. (= hotter).
So don't trust the original instruction manual, things change with the time!!
( I had the same experience with my Chevy V-8, plugs fouling every few hundred miles..turned out to be the exact same thing...AC Delco changed their advice, I had to use hotter plugs than standard!)
User avatar
78SS
Cucciolo - the Lil Pup
Posts: 9
Joined: Mon Feb 05, 2007 6:02 pm
Location: New Zealand
Contact:

Post by 78SS »

As far as I know its standard compression, it did run fine on leaded gas with the same octane rating. Might need hotter plugs to burn off residue from combustion, as I have mentioned I do not think unleaded combusts properly like leaded gas as there is a oily residue left in tail pipe.
Rick F
Mach 3
Posts: 89
Joined: Mon Aug 07, 2006 6:35 pm
Location: Murwillumbah NSW AUstralia

question unanswered

Post by Rick F »

So gents,
it got a little like a political forum, skirting the question but never really answering it!

It sounds to me like there are a lot of opinions out there about this.

I am a little uninformed, (a builder, not a mechanic or engineer), but if someone in the profession that I trust says to throw a bit in the tank every now and then, I do....I buy the bottle and follow the instructions, and hope that it cant hurt! Pirsig would cringe!

Yes I am running high octane unleaded anyway, people I have known that do know what they are talking about say that the standard Unleaded here in OZ is dog doodie, so premium is the go....but for every thing except the cars. I use premium in the ride-on mower, the outboard motor, the brushcutter.
and it does seem to improve the reliability.....no major failures or carb rebuilds etc.

So when I 1st got the bike back in 1986, (my 3rd GT) it had a rebuilt unstarted motor, with Sport pistons and valves. Apparently. It was a long time ago.

What way are the valves different? would they cope with unleaded better than standard valves? (premium unleaded)

Rick
MartinMille BANNED
BANNED
Posts: 766
Joined: Fri Sep 21, 2007 8:15 pm

Post by MartinMille BANNED »

Hi Rick
I use Valvemaster and have for years ,you sure notice the difference when you run out of the stuff , the Mille starts to ping its heads off and has lack of power add valvemaster and within 5 min's she purr's again
get some and try it
Rick F
Mach 3
Posts: 89
Joined: Mon Aug 07, 2006 6:35 pm
Location: Murwillumbah NSW AUstralia

Valvemaster

Post by Rick F »

Hi Martin,
I have been using the valvemaster since I put the bike back on the road.

I am not too far from Arthur at Byron Bay and it was he that prompted my questions....ie just thro a bit in every few tankfuls.

As I say, I am religous with it and it seems to make the ride-on go a bit better as well!

Whereabouts are you?

Rick
Post Reply

Return to “Carburettor & Fuel System Shop”