Darmah Front cylinder running rich

Post your 'Carburettor & Fuel System' FAQs, comments & questions regarding Ducati motorcycles here.
User avatar
Craig in France
Cagiva Gran Canyon
Posts: 894
Joined: Tue Mar 23, 2004 3:58 pm
Location: Montpellier, France

Re: Darmah Front cylinder running rich

Post by Craig in France »

mdal8798 wrote:
Wed Jul 22, 2020 1:19 am
Pickups and wiring are are in good condition ... Resistance measurements are within specification <snip>
Well, I guess that's progress, Mark ... in a way :roll:

So, is it still banging and popping on the front? Back to basics, then:
- Have you checked the valve clearances?
- Don't forget the plug cap and lead (Unscrew the cap, cut the lead back a tad, wipe it clean, re-fit the cap. Use a new one, by preference - and of the right resistance)
- Check the quality of the connection at the coil too
- And of course fit a new plug
- You could also try swapping coils
- Exhaust sealing properly?
mdal8798 wrote:
Wed Jul 22, 2020 1:19 am
I have contacted Gowanlochs in Sydney ... he is of the belief that i just need to get bike on the road and basically blow the cobwebs out of it first then look at idle setup later.
I will freely admit that this kind of advice, especially when coming for a professional, always concerns me. Because if something is wrong, 'running it down the road for a few miles' it just as likely to make things worse as to magically resolve the problem. But each to their own ...

The advice from 900tlc about changing the ignition system is well-founded, however. All depends on how much time and money you have, and how frustrated you get chasing faults :evil:

@ 81mhr900ss: excellent advice as always. However, when Mark swapped the carbs over, the problem (banging and popping) stayed with the same cylinder (the front). Which suggests that the problem is not carb related.

User avatar
81mhr900ss
Parallel Twin
Posts: 113
Joined: Tue May 31, 2016 3:49 pm

Re: Darmah Front cylinder running rich

Post by 81mhr900ss »

Understood and agreed. After pulling out all the old stuff, I was able to determine that the likely culprit for my initial pre-Sachse lumpiness was the front coil. I'm very happy with the decision to go with a new ignition system.

User avatar
Craig in France
Cagiva Gran Canyon
Posts: 894
Joined: Tue Mar 23, 2004 3:58 pm
Location: Montpellier, France

Re: Darmah Front cylinder running rich

Post by Craig in France »

81mhr900ss wrote:
Thu Jul 23, 2020 8:40 pm
Understood and agreed. After pulling out all the old stuff, I was able to determine that the likely culprit for my initial pre-Sachse lumpiness was the front coil. I'm very happy with the decision to go with a new ignition system.
Thanks for the info. Tell me, did you have Motoplat (red) or Nippon Denso (off white) coils ? Just being nosey ... :-D

User avatar
81mhr900ss
Parallel Twin
Posts: 113
Joined: Tue May 31, 2016 3:49 pm

Re: Darmah Front cylinder running rich

Post by 81mhr900ss »

Nippon Denso were the original coils on my 81 MHR
Last edited by 81mhr900ss on Sat Jul 25, 2020 4:06 pm, edited 1 time in total.

User avatar
Craig in France
Cagiva Gran Canyon
Posts: 894
Joined: Tue Mar 23, 2004 3:58 pm
Location: Montpellier, France

Re: Darmah Front cylinder running rich

Post by Craig in France »

81mhr900ss wrote:
Fri Jul 24, 2020 11:23 am
Nippon Denso were the original coils
And sometimes Motoplat :). But I guess you had N-D, right?

Post Reply

Return to “Carburettor & Fuel System Shop”