250 cafe custom, #2

Post pictures of your single cylinder Ducati along with a description here.
joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

250 cafe custom, #2

Post by joe1028 » Thu Jun 24, 2010 6:43 pm

Imagehi, one of the cafe bikes finished up...
Last edited by joe1028 on Thu Jun 24, 2010 7:26 pm, edited 1 time in total.

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

duc 250

Post by joe1028 » Thu Jun 24, 2010 6:44 pm

Image

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

Post by joe1028 » Thu Jun 24, 2010 6:45 pm

Image

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

Post by joe1028 » Thu Jun 24, 2010 6:46 pm

Image

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

Post by joe1028 » Thu Jun 24, 2010 7:28 pm

Image
duc 250 and cb 750 cafe machines finished up last month

TDF
Mariana
Posts: 30
Joined: Sat Jun 20, 2009 4:33 pm
Location: Emerald Nebraska, USA

Post by TDF » Fri Jun 25, 2010 2:20 pm

I love it, wish mine looked that good. Did you make the tank or buy it somewhere?

TDF
1966 Ducati 350 Sebring
1965 Ducati Bronco 125
1958 MDS Super Dart
2000 Moto Guzzi V11 Sport
2002 MV Agusta F4 750
Plus a whole herd of non-Italian motorcycles.

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

Post by joe1028 » Fri Jun 25, 2010 11:35 pm

the tank /tail section is stock from airtech but modified for the narrow case.(slightly)

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

Post by joe1028 » Fri Jun 25, 2010 11:37 pm

Image
under lh cover..heat formed abs inner fender,battery strap,cover brackets with rivnuts,clip in fuses and charge light.

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

Post by joe1028 » Fri Jun 25, 2010 11:41 pm

Image
adjustable resistor for led tail light(running-brake off position) which was made up with 20 clear 3.3 v 25 ma leds, 110ohm resistors and then soldered onto a circuit board which was wired and mounted under the tail section to the frame.

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

Post by joe1028 » Fri Jun 25, 2010 11:45 pm

Image alum mirror with modified s/s attach hardware

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

Post by joe1028 » Fri Jun 25, 2010 11:47 pm

Image
engine plates and hand removable oil dip stick with friction tab so cap will not come loose.

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

Post by joe1028 » Fri Jun 25, 2010 11:48 pm

Image
operational airscoop and drilled lever.

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

Post by joe1028 » Fri Jun 25, 2010 11:50 pm

Image

joe1028
Mariana
Posts: 30
Joined: Fri Mar 21, 2008 3:39 pm
Location: msp

Post by joe1028 » Fri Jun 25, 2010 11:52 pm

Image alum pts cover,s/s retention straps.

User avatar
BevHevSteve
SITE OWNER
SITE OWNER
Posts: 2114
Joined: Wed Mar 10, 2004 8:53 pm
Location: Lafayette, California
Contact:

Post by BevHevSteve » Mon Jun 28, 2010 7:28 am

sweet bike

looks a treat, thanks for sharing the pix. Recommend you coat that tank with CASWELL tank sealer B4 putting gas in there.
Image
Steve Allen (925)798-BEVL[2385] Ride'm, Don't Hide'm
Ducati/Euro Spares -> https://Store.BevelHeaven.com
Facebook > http://facebook.com/Bevel.Heaven
Twitter > http://www.Twitter.com/BevelHeaven

Post Reply

Return to “Single Cylinder Photo Gallery”