Search found 10 matches

by Mark Burling
Tue Nov 06, 2007 11:49 am
Forum: Body, Paint & Rubber Shop
Topic: Looking for a S2 Bellypan ...
Replies: 1
Views: 1716

Don't know where you're based. Noticed S2 fairings at my mechanics last time I was there. Am in New Zealand.
by Mark Burling
Tue Nov 06, 2007 11:44 am
Forum: Body, Paint & Rubber Shop
Topic: Frame paint
Replies: 4
Views: 4026

I always powder coat frames as its very hard to spray a frame evenly! Also although 2k is pretty hard, powder coating is more resilient. Its a good idea to get things like triple clamps and headlight mounts done with the frame. Parts really need sand blasting b4 coating, gives a really good key. Hop...
by Mark Burling
Wed Oct 31, 2007 8:20 pm
Forum: Engine & Transmission Shop
Topic: Fitting Mille oil pump to 900 engine
Replies: 0
Views: 1254

Fitting Mille oil pump to 900 engine

We are nearing the completion of a race motor and are hoping to fit a mille oil pump but have found the drive doesn't line up. Does anyone know of a gear available to make it work? does the Mille have a dished gear or similar and if so are they available?
by Mark Burling
Wed Aug 09, 2006 3:23 pm
Forum: Squarecase Early 860/900 Crossover Gearchange Engines > 860/900 GT
Topic: poor starting on gts
Replies: 1
Views: 2078

Could be a leaky inlet manifold causing it to run lean when hot.
by Mark Burling
Sat Aug 05, 2006 4:02 pm
Forum: Bevel Drive Twins
Topic: 40mm inlet manifolds wtd
Replies: 0
Views: 1143

40mm inlet manifolds wtd

I need 40mm dellortos to bevel desmo. Would prefer straight for rear cylinder. Am In New Zealand but happy to pay freight. May trade other parts. ;)
by Mark Burling
Thu Aug 03, 2006 2:56 pm
Forum: Pit Lane
Topic: racing a bevel head
Replies: 5
Views: 10050

Engine is now being built by Bruce Telford and head work being done by Collier engineers. Fitting 44mm inlet and std 36mm exaust. Running slipper bearing moded crank. Am changing swing arm by cutting a solid axle swing arm, slotting and fitting adjuster blocks (SS and MHR parts.). Frams is down to b...
by Mark Burling
Thu Nov 04, 2004 12:32 pm
Forum: Electrical & Gauges Shop
Topic: DIY Wiring Loom For Bevels - How Hard Can It Be?
Replies: 15
Views: 8639

Doing loom now

I am currentlt fitting a new loom to my SSD, one of the last jobs from full build. I have found most of the wiring digrams I have downloaded don't relate to any of the three looms I have (two std darmah and one built up) I am happy to take some photo's of a standard loom out of bike if stiil require...
by Mark Burling
Tue Aug 31, 2004 9:03 pm
Forum: Pit Lane
Topic: racing a bevel head
Replies: 5
Views: 10050

Racing Bevel

I am just about to start building a 79' Bevel Drive race bike. I have a modified crank, imola cams am looking at having upto 44mm inlet valves, I also have a mille oil pump, SS left side engine cover (to do away with starter). Chassis has had steering head steepened, swingarm shortened. I hav'nt pic...
by Mark Burling
Tue Aug 31, 2004 1:50 pm
Forum: Wheel, Brake & Tyre Shop
Topic: Spoked Wheels : Who are the best suppliers to know?
Replies: 15
Views: 9761

Wheels

Steve Greene In NZ has Ducati Twins Restoration Guide. $115.00 NZD stevegreen@xtra.co.nz I have two FPS rear rims and no front rims to use on a 79' SS Darmah race bike I am about to start work on. I am told you can have the rear machined down to fit front. Who would do this and are thier better opti...
by Mark Burling
Sat Aug 28, 2004 5:32 pm
Forum: Bevel Drive Twins
Topic: Selling some more left over bevelstuff.....
Replies: 2
Views: 2809

Am interested in fps rims, clip ons, front head, conti's, for darmah.

Cheers
Mark

Go to advanced search